ALBEDO Ether.Sync is a field tester for Synchronous Ethernet equipped with all the feature to deploy and troubleshoot both GbE and SyncE infrastructures, supporting standards such as Y.1564 & Y.1731 to verify the QoS and SLA to quickly and easily validate and troubleshoot ANY Ethernet service.
Ether.Sync adds new features for the installation and maintenance of new Synchronous technologies while conserving everything required for the commissioning and troubleshooting of Gigabit Ethernet.
Ethernet Line frequency (MHz), offset (ppm), drift (ppm/s)
Analysis / Generation ESMC messages and SSM count and rate
Ext. clock input including 2048 kb/s, 2048 Hz, and Synchronous Ethernet
SyncE MTIE / TDEV measurement
SyncE Wander analysis/generation
PTP / IEEE 1588v2 support decoding
PTP support / generation as master or slave
Master Clock operation on each port using internal/external ref.
Y.1564 (e-SAM) FTD, 2-way FDV, FDV, 2-way FTD, FLR, SES, PEU & PEA
Y.1731 QoS statistics
2xSFP + 2 x RJ45 i/faces
Symmetrical & Asymmetrical RFC2544 test
FCS error insertion in pass-through mode
Multistreams for IPTV, VoIP, and Critical Data verification
Q-in-Q for demarcation tests
Advanced Counts: Up to 8 filters at MAC, IP, TCP/UDP, Arbitrary
QoS and SLA certification
Automatic RFC2544, Y1464
pdf & csv reports on SD/USB
IPTV, VoIP, Data assurance
VNC, LAN or wi-fi control
Spot sources of degradation
s-LEDs all events at a glance
Best price - Top featured
Triple Play service providers
Commission / Maintenance
Ether.Sync hand-held tester. Battery operated. GBE testing with synchronization options including dual 10/100/1000 Mb/s RJ-45 electrical ports, dual optical ports, QoS statistics, RFC2544 performance test, BER test, continuous / burst / ramp / random traffic generation, traffic statistics, error analysis, connectivity test (PING, Trace Route), analysis filters, event insertion, endpoint and pass-through operation modes, graphical display of events, report generation and export. Includes AC/DC adapter, transportation bag and one RJ-45 patch cable. SFP transceivers not included.
Multistream Test. Generation over eight independent traffic streams. Eight analysis filters for each test port.
eSAM (ITU-T Y.1564). Test of up to 8 services simultaneously. Set up of CIR, EIR and policing rate. Per stream quality objectives. Measurement of Information rate (IR), Frame Transfer Delay (FTD), Frame Delay Variation (FDV), Frame Loss Ratio (FLR) and Availability. [REQUIRES: AT.ESync.Mstr]
IPV6 test. Decoding and analysis of IPV6 datagrams. IPV6 traffic statistics and events. IPV6 packet filtering. Top IPV6 source and destination address (with Network Search option).
MPLS test. Generation of a single or double label according RFC 3032. Configuration of TTL, Traffic class, Label . Filter selection rules by Label and Traffic class field. Frame analysis of MPLS Packets. Top LSPs (with Network search option).
Cable test. Wiremap with open and short circuit detection. Measurement of distance to fault. Crossover / straight cable detection. Measurement of the cable skew.
Power over Ethernet test. PoE / PoE+ end point and pass through as per IEEE 802.3af and IEEE 802.3at with voltage and current measurement.
SyncE clock emulation. Synchronization testing according to ITU-T G.8261, G.8262, G.8264. Ethernet line frequency (MHz), offset (ppm), drift (ppm/s). Analysis / Generation of ESMC messages. External reference clock input 2048 kbit/s, 2048 kHz, 1544 kbit/s, 1544 kHz, 10 MHz, Synchronous Ethernet and 1 PPS. External reference clock output 2048 kHz and 1 PPS.
Car charger. Power adapter to charge the test unit from car battery.
Additional Lipo battery
Certificate of calibration. Accuracy calibration certificate, executed only when is sold and before its shipment.
Periodical Unit Verification. Includes board test verification (Calibration, Internal Frequency), test port verification (Ports A / B / C: Ethernet, SFP, unbalanced E1, balanced E1, VF Port , DTE / DCE Ports) and analog verification (level port A / B / C, line attenuation, jitter error, pulse mask).